D.1 PJLink Command list

Supported PJLink Commands
CommandDescriptionRemarks
POWRPower control

Parameters:

  • Power on = Switch projector to ON mode

  • Power off =

    • When projector is in ON mode, go to Ready mode.
    • When projector is in READY mode, go to (Eco) Standby.
    • When projector is in READY mode and (Eco) Standby mode is disabled, remain in READY mode.
INPTSwitch source

Parameters:

  • Instruction to switch input to RGB (class 1) is not supported
  • Instruction to switch input to RGB (class 2) is not supported
  • Instruction to switch input to Video (class 1) is not supported
  • Instruction to switch input to Video (class 2) is not supported
  • Instruction to switch input to Storage (class 2) is not supported
  • Instruction to switch input to Network (class 2) is not supported
  • Instruction to switch input to Internal (class 2) is not supported
  • Instruction to switch input to Digital (Class 1) is only available when the projector is in ON or READY mode.
  • Instruction to switch input to Storage (Class 1) is only available when the projector is in ON or READY mode.
  • Instruction to switch input to Network (Class 1) is only available when the projector is in ON or READY mode.
  • Instruction to switch input to Digital (Class 2) is only available when the projector is in ON or READY mode.

Remark for PJLink Class 1 only: The PJLink 1.0 specification only defines 9 digital inputs. Barco projectors can have more than 9 digital inputs. For this reason, the storage and network categories are used to host the remaining digital sources. This will result in the following:

  • Source 01 - 09 = PJLink input 31 - 39
  • Source 10 - 18 = PJLink input 41 - 49
  • Source 19 - 27 = PJLink input 51 - 59

Note: The projector sources are defined by numbers instead of names. This is because the exact source depends on the input cards used and their position in the Input and Communication unit. The first source will correspondend with the first item in the list provided by the command “image.source.list”.

AVMTMute audio and/or video

Parameters:

  • Video mute = ON >> Shutter closes
  • Video mute = OFF >> Shutter opens
  • Audio mute is not supported
  • Audio & video mute is not supported

Note: Command is only available when projector is in ON or READY mode.

SVOLAdjust Speaker volumeCommand not supported
MVOLAdjust microphone volumeCommand not supported
FREZFreeze the screenCommand not supported
POWR?Get power status

Parameters:

  • Power on = projector is in ON mode
  • Power off = projector is either in READY, STANDBY or ECO STANDBY mode.
  • Cooling status = projector is in the deconditioning status
  • Warmup status = projector is in the conditioning status
INPT ?Get current source 
AVMT ?Get the audio/video mute status

Parameters:

  • Video mute on >> Shutter closes
  • Video mute off >> Shutter opens
  • Audio mute is not supported
  • Audio & video mute is not supported

Note: Command is only available when projector is in ON or READY mode.

ERST ?Get error statusOnly “other errors” as a parameter is supported.
LAMP ?Get status of the lampCommand not supported
INST ?Get list of input sources 
NAME ?Get projector nameThe result is the projector Hostname
INF1 ?Get manufacturer of the projectorThe result is: “Barco”
INF2 ?Get product nameIdentification property of the DeviceIdentification file
INFO ?Get other infoCommand not supported
CLSS ?Get PJlink classThe result is “2”
SNUM ?Get serial number 
SVER ?Get software version 
INMM ?Get name of the input sources 
IRES ?Get input resolution

Only supported with single source selection.

Not supported when stitched connections are used.

RRES ?Get recommended resolution 
FILT ?Get wear counter of filerCommand not supported
RLMP ?Get lamp replacement model numberCommand not supported
RFIL ?Get filter replacement model numberCommand not supported
FREZ ?Get status of the freeze control functionCommand not supported