About communication

Configure the settings that allow the projector to communicate with other projectors, or control devices.

Projector ID

Assign a remote code for the projector from 00 to 99.

Use this code as the projector ID when controlling the projector by:

• RS232
• HDBaseT
• Telnet
• Other control methods

Remote setup

Configures the settings of the Infra-Red (IR) remote control.

• Remote code:

  Assign a remote code from 00 to 99 for the remote receivers on the projector. The projector only responds to the IR remote control set with the same remote code.

• Remote receiver:

  Sets the remote receiver for the projector to control the communication between the projector and the IR remote.

  • Front:

    Enable or disable the front remote receiver.

  • Top:

    Enable or disable the top remote receiver.

  • HDBaseT:

    Select On to set the HDBaseT terminal as the remote receiver.

• User button1 / user button2:

  Assign a function to the user1 / user2 buttons on the remote control, allowing you to use the function easily without having to go through the OSD menus.

Network setup

Configure the projector’s network settings.

• Ethernet:

  Configure the projector’s ethernet settings when connecting to a wired network using an “RJ-45 cable”.

  • LAN interface:

    Specify the LAN interface to either RJ-45 or HDBaseT.

  • MAC address:

    Display the MAC address. (Read only)

  • Network status:

    Display the network connection status. (Read only)

  • DHCP:

    Turn on DHCP to automatically acquire the IP address, subnet mask, gateway, and DNS.

  • IP address:

    Assign the projector’s IP address.

  • Subnet mask:

    Assign the projector’s subnet mask.

  • Gateway:

    Assign the projector’s gateway.

  • DNS:

    Assign the projector’s DNS.

  • Apply:

    Apply the wired network settings.

• Reset:

  Reset all network settings to their default factory values.

Email notification

The user can setup email notifications for some events, which allows them to receive early alerts via emails.

• Email:

  Display the email addresses set up on the web control panel. Up to two emails can be set to receive the notifications. (Read Only)

• Event:

  The events support email notification include Light Source Fault, Fan Stall, Thermal Sensors, Power, and Signal Lost/Detected. The user can send early alerts via email to one of the email address or both.

• Reset:

  Resets all email notifications to their default factory values.

Control

This projector can be controlled remotely by a computer or other external devices through wireless or wired network connection.

It allows the user to control one or more projectors from a distant control center, such as powering the projector on or off and adjusting the image brightness or contrast.

• Crestron:

  Control the projector with a Crestron controller and its related software. (Port: 41794) You can configure the IP Address, IPID, and Port for the network connection. For more information, please visit http://www.crestron.com.

• Extron:

  Control the projector with Extron devices. For more information, please visit http://www.extron.com.

• PJLink:

  Control the projector with PJLink v1.0 commands. You can configure the IP Address (Service) for the network connection. For more information, please visit http://pjlink.jbmia.or.jp/english.

• Service:

  Configure the IP Address (Service) for PJLink control.

• PJLink setup apply:

  Apply the PJLink network configurations.

• AMX:

  Control the projector with AMX devices. For more information, please visit http://www.amx.com.

• Telnet:

  Control the projector using RS232 commands though a Telnet connection.

• HTTP:

  Control the projector with a web browser.

• Cloud:

  Control the projector to enable or disable the IMS(Insights Management Suite) feature.

• Reset:

  Resets the control settings to their default factory values.

Note: Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.

Extron is a registered trademark of Extron Electronics, Inc. of the United States.

AMX is a registered trademark of AMX LLC of the United States.

PJLink applied for trademark and logo registration in Japan, the United States of America, and other countries by JBMIA.

Tip: For more information about the various types of external devices which can be connected to the LAN/ RJ45 port and remotely control the projector, as well as the supported commands for these external devices, please contact the Support-Service directly.

Baud rate

Set the baud rate for the serial port.

Reset

Resets all the communication settings to their factory default values.