Download
SHA256 checksum
46870a78de6ad5f40c07b14c95e3aaa0e46a55b97cbf575fa4239d692275aa22
Release notes
Event Master Toolset Version 9.1 Build 67065
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
- Use the following with this release of EM firmware.
- PDS-4K Firmware: pds_update_vp.enc.9.1.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Firmware: em_update_vp.9.1.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Operating System: em_update_os.3.1.1.tar.gz
- Please note: OS of E2/S3/EX/ImagePRO-4K is now the same. It can only be installed after the firmware has been upgraded to at least 7.0.
KNOWN ISSUES
- EM: There is no intended use for enabling the DisplayID Block for use with single connector inputs/backgrounds and if enabled with such may cause the input to stop displaying picture until the chassis is soft reset (power cycled).
- EM: Due to certain LAN configurations, it is possible that backup operations can succeed but restore operations can fail from the web app.
- EM: There is a known issue with Atomos Shogun not creating valid CRC streams per SMPTE ST-2081/2082 at 6/12G-SDI rates and as such the Tri-Combo Input does not acquire its signal.
- PDS-4K: HDMI 1.4 devices that output UHD at 50/59.94/60 with 4:2:0 chroma sub-sampling may not be acquired.
- PDS-4K: Audio Option Card: When running the Dante Card in Redundant Ethernet mode, the IP Address information for the Secondary Ethernet Conenctor (#2) that shows on the Front Panel and the GUI will be incorrect.
- EC-210: See What's New file.
BUG FIXES
- EM: Multi-Op: Preset recall would deselect Aux destination(s) under control of other operator(s).
- EM: Multi-Op: Preset recall of Super Dests were only changing for the Super Operator and not a Normal Operator.
- EM: Unable to select a 5760x1080 still store image as a backup for Background Input with the same resolution.
- EM: Sizing Adjustment of an Input source's V Pos while the Layer Position Center of Destination option is turned on would display the starting position incorrectly.
- EM: With the System Native Rate less than or equal to 30Hz, 6G-SDI inputs, which require 4K capacity were allowed to be used in DL scaling resources and resulted in other related issues.
- EM: Ex connected via CXP I/O card was incorrectly causing a "Global Link resources exceeded" error when the Global Link switch was toggled.
- EM: Certain linked chassis configurations would experience "lag" in the GUI when using the mouse to position a layer on PVW.
- EM: I/O configured on daisy-chained EX chassis were not showing good video in the host chassis' MVR windows.
- EM: When multiple Screen Destinations had a test patterns on, then turned off, the UMD notification would still show the test pattern was on.
- EC: Quickly changing the function of the assign bus(es) caused the EMTS to crash.
- IP4K: When the output format was set to 1080i the Front Panel Status showed the output format as 1080p.
- PDS-4K: Preset/Cues button mapping was reverting to an auto-mapped state after power cycle.
- PDS-4K: Running a System Diagnostic via the front panel menu would incorrectly report a failure.
- PDS-4K: Masking the left side of a UHD60 input >50% would show the left half of the input on the right half.
NEW FEATURES
- PDS-4K: For models with SDI connectors and the Audio Option Card installed, added capability for two channels of embedded audio on SDI Input and Output connectors as well as disembed two channels for each SDI input's audio to Dante.
