Event Master toolset Win (Release 9.2 Build 68334)
- Version
- v9.2.0.0
- File size
- 71 MB
- Release date
- 12 Oct 2023
- Available for
- SHA256 checksum
- e18988d22786116524e24adaf9ff5416057691953d323dd91d9a5d024fb3367b
Release notes
Event Master Toolset Version 9.2 Build 68334
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
- Use the following with this release of EM firmware.
- PDS-4K Firmware: pds_update_vp.enc.9.2.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Firmware: em_update_vp.9.2.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Operating System: em_update_os.3.1.1.tar.gz
- Please note: OS of E2/S3/EX/ImagePRO-4K is now the same. It can only be installed after the firmware has been upgraded to at least 7.0.xxxx
- EM: There is no intended use for enabling the DisplayID Block for use with single connector inputs/backgrounds and if enabled with such may cause the input to stop displaying picture until the chassis is soft reset (power cycled).
- EM: Due to certain LAN configurations, it is possible that backup operations can succeed but restore operations can fail from the web app.
- EM: There is a known issue with Atomos Shogun not creating valid CRC streams per SMPTE ST-2081/2082 at 6/12G-SDI rates and as such the Tri-Combo Input does not acquire its signal.
- PDS-4K: See What's New file.
- EC-210: See What's New file.
- EM: Rare but possible crash in unstable network environment.
- EM: Inputs from a daisy-chained EX were not visible in the multiviewer.
- EM: Single Layers assigned to a Screen Destination within a Super Destination were changing layers on locked Program.
- EM: Screen Destinations that use more than one row of canvas links could show an artifact.
- EM: Diagnostic error message on S3 with one PSU.
- EM: JSON armUnarmDestination followed by allTrans resulted in transitioning unarmed Destinatations.
- EC: See What's New file.
- IP4K: See What's New file.
- PDS-4K: See What's New file.
- EM: Any SuperLayer(s) assigned to Super Destination(s) can either act Globally or Locally.
- EM: User preference for "Destination Tabs add on the Right" upon creation.
- EM: Backup files exported from the WebApp now appends the date and time to the filename’s characters.
- EM: The HDCP status for supported output connectors is now available when an output connector is selected.
- EC: See What's New file.
- PDS-4K: See What's New file.
- EM: Tally indications in the Multiviewer UMDs and GUI’s Programming Page for Multi-Operator use (Gen2 MVR card required).
- EM: Multi-Select Destination Tabs to add them to Programming Layouts by using Ctrl+Click (Mac: Cmd+Click).
- EM: Backgrounds as Source (Inputs Tab) now has New Source and Copy Source buttons.
- EM: Custom Format’s VESA calculator section now defaults to having the Reduced Blanking Version 1 option applied.
- EM: For Aux Destinations the Aux Scaling Mode is now defaulted to "Custom" instead of "All."
- EM: JSON Commands added, changeSuperDestContent and changeSuperAuxContent
- IP4K: See What's New file.
- PDS-4K: See What's New file.
Version history
SHA256 checksum
46870a78de6ad5f40c07b14c95e3aaa0e46a55b97cbf575fa4239d692275aa22
Release notes
Event Master Toolset Version 9.1 Build 67065
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
Download
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
- Use the following with this release of EM firmware.
- PDS-4K Firmware: pds_update_vp.enc.9.1.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Firmware: em_update_vp.9.1.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Operating System: em_update_os.3.1.1.tar.gz
- Please note: OS of E2/S3/EX/ImagePRO-4K is now the same. It can only be installed after the firmware has been upgraded to at least 7.0.
- EM: There is no intended use for enabling the DisplayID Block for use with single connector inputs/backgrounds and if enabled with such may cause the input to stop displaying picture until the chassis is soft reset (power cycled).
- EM: Due to certain LAN configurations, it is possible that backup operations can succeed but restore operations can fail from the web app.
- EM: There is a known issue with Atomos Shogun not creating valid CRC streams per SMPTE ST-2081/2082 at 6/12G-SDI rates and as such the Tri-Combo Input does not acquire its signal.
- PDS-4K: HDMI 1.4 devices that output UHD at 50/59.94/60 with 4:2:0 chroma sub-sampling may not be acquired.
- PDS-4K: Audio Option Card: When running the Dante Card in Redundant Ethernet mode, the IP Address information for the Secondary Ethernet Conenctor (#2) that shows on the Front Panel and the GUI will be incorrect.
- EC-210: See What's New file.
- EM: Multi-Op: Preset recall would deselect Aux destination(s) under control of other operator(s).
- EM: Multi-Op: Preset recall of Super Dests were only changing for the Super Operator and not a Normal Operator.
- EM: Unable to select a 5760x1080 still store image as a backup for Background Input with the same resolution.
- EM: Sizing Adjustment of an Input source's V Pos while the Layer Position Center of Destination option is turned on would display the starting position incorrectly.
- EM: With the System Native Rate less than or equal to 30Hz, 6G-SDI inputs, which require 4K capacity were allowed to be used in DL scaling resources and resulted in other related issues.
- EM: Ex connected via CXP I/O card was incorrectly causing a "Global Link resources exceeded" error when the Global Link switch was toggled.
- EM: Certain linked chassis configurations would experience "lag" in the GUI when using the mouse to position a layer on PVW.
- EM: I/O configured on daisy-chained EX chassis were not showing good video in the host chassis' MVR windows.
- EM: When multiple Screen Destinations had a test patterns on, then turned off, the UMD notification would still show the test pattern was on.
- EC: Quickly changing the function of the assign bus(es) caused the EMTS to crash.
- IP4K: When the output format was set to 1080i the Front Panel Status showed the output format as 1080p.
- PDS-4K: Preset/Cues button mapping was reverting to an auto-mapped state after power cycle.
- PDS-4K: Running a System Diagnostic via the front panel menu would incorrectly report a failure.
- PDS-4K: Masking the left side of a UHD60 input >50% would show the left half of the input on the right half.
- PDS-4K: For models with SDI connectors and the Audio Option Card installed, added capability for two channels of embedded audio on SDI Input and Output connectors as well as disembed two channels for each SDI input's audio to Dante.
SHA256 checksum
349ccf5e2562a3fa62896545d07f581a8d116e6f542f41092f7dddc0cc4a3726
Release notes
Event Master Toolset Version 9.0 Build 65399
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
Download
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
- Use the following with this release of EM firmware.
- PDS-4K Firmware: pds_update_vp.enc.9.0.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Firmware: em_update_vp.9.0.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Operating System: em_update_os.3.1.1.tar.gz
- Please note: OS of E2/S3/EX/ImagePRO-4K is now the same. It can only be installed after the firmware has been upgraded to at least 7.0.
- EM: There is no intended use for enabling the DisplayID Block for use with single connector inputs/backgrounds and if enabled with such may cause the input to stop displaying picture until the chassis is soft reset (power cycled).
- EM: Due to certain LAN configurations, it is possible that backup operations can succeed but restore operations can fail from the web app.
- EM: There is a known issue with Atomos Shogun not creating valid CRC streams per SMPTE ST-2081/2082 at 6/12G-SDI rates and as such the Tri-Combo Input does not acquire its signal.
- PDS-4K: HDMI 1.4 devices that output UHD at 50/59.94/60 with 4:2:0 chroma sub-sampling may not be acquired.
- PDS-4K: Audio Option Card: When running the Dante Card in Redundant Ethernet mode, the IP Address information for the Secondary Ethernet Conenctor (#2) that shows on the Front Panel and the GUI will be incorrect.
- EC-210: Left Monitor Grey: Certain conditions may cause the left monitor to start with the "External Input" check box turned on, even when there is no input device attached.
- EC-210: Sometimes when an external display is plugged in after the EC-210 has booted, one or more of the screens may show grey.
- EC-210: It is not possible to setup a Class B subnet on the EC-210 controller.
- EM: Added a way to sort linked Chassis in the workspace by unit ID in ascending or descending order.
- EM: Added a GUI layer "Transparent Mode" control to enable the user to see layers lower in the z-order while keeping the content visible in the GUI.
- EM: Tooltip for Destination Names shows name of Destination that may have become truncated.
- EC: Added Syntax for Backup and Primary Input(s) control.
- IP4K: Added the "Non-Compliant Device" control to the Front Panel EDID menus on DP1.2 inputs.
- PDS-4K: Added support new DisplayPort Input and Audio (plus Dante) processing card. Barco P/N: R9802040
- PDS-4K: Added Keying. Luma and Chroma Key capability is now available on single layers.
- PDS-4K: Added HDR and Wide Color Gamut support.
- PDS-4K: Added Auto System Setup to the GUI.
- EM: An input's PGM Tally State will change as soon as the Input begins to transition to PGM.
- EM: Presets and External Devices and commands can be renamed on the Cue Menu page.
- EM: Added a "Switch Operator" button to the top left corner of the GUI
- PDS-4K: The GUI's simulator tab can now change the base model as well as allow the DP1.2 and Audio card to be simulated.
- PDS-4K: The GUI's Custom Format tab is updated to only show the possible connectors that may be available on a PDS-4K unit.
- PDS-4K: SDI inputs will now accept PsF formats.
- PDS-4K: When Auto Take is off (default) the GUI shows the Preset recall mode is "Preset to PVW." When Auto take is on the GUI changes the Preset recall mode to "Preset to PGM."
SHA256 checksum
1ba22418860fee960f3870367360e1cbf169a66ee0fc814613fa0aad1e6c6e36
Release notes
Event Master Toolset Version 8.2 Build 64229 (Maintenance Release)
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
Download
Please read the What's New file after downloading this bundle for more detailed information about these features.
IMPORTANT NOTES
- Use the following with this release of EM firmware.
- PDS-4K Firmware: pds_update_vp.enc.8.2.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Firmware: em_update_vp.8.2.xxxx.tar.gz or higher
- E2/S3/EX/ImagePRO-4K Operating System: em_update_os.3.1.1.tar.gz
- Please note: OS of E2/S3/EX/ImagePRO-4K is now the same. It can only be installed after the firmware has been upgraded to at least 7.0.
- Fix an issue with MVR as Source in E2 to EX linked systems not showing on Aux destinations configured on the EX chassis
- Fixed an issue in the GUI's Programming page that did not allow the user to sort the Destination Tabs in their preferred order
- Fix an error of incorrect calculations for power load/PSU redundancy that causes a warning message to pop up in the GUI